欢迎进入成都华枢通信官网,我们的产品有:工业交换机(环网交换机)、光纤交换机、交换机模块、定制模块、定制板卡、工业级光纤收发器、网络延长器、4G/5G工业路由器、4G/5G物联网网关。

Rail-non network management

HS-6206 Series 6-port industrial switch with non-network management and rail

Full Gigabit | 2 optical ports + 4 electrical ports | non network management type

  • Model: HS-6206A-2GSFP
  • Management: Non-network management
  • Installation_method: Guideway
  • NO.ports(RJ45): 4
  • Port_rate(RJ45): 1000M
  • Optical_port_type: SFP(LC/SC)
  • NO.SFP_(LC/SC): 2
  • Supply_voltage: DC24V,DC12V
  • NO.power_input_groups: Double
  • Temperature_range: -40℃~75℃
  • Serial_port_type: RS232

Main Features:

  • Comply with IEEE 802.3 10 Mbps Ethernet standard, IEEE 802.3u 100 Mbps Ethernet standard, IEEE 802.3ab 1000 Mbps Ethernet standard, IEEE 802.3x flow control standard;

  • Store and forward switching mechanism is adopted to support rate adaptability and ensure data integrity;

  • Support full duplex / half duplex automatic monitoring, adaptive communication mode and MDI / mdi-x port adaptive, cross line and through line can be used freely;

  • Non blocking switching structure, full line speed forwarding;

  • Port automatic MAC address learning and aging function;

  • Port LED status indication, which can easily detect the link connection, rate, data receiving and sending status of each port;

  • The alarm of power supply, optical fiber port and RJ45 electric port can be set flexibly. At the same time, it supports led, menu alarm prompt and relay alarm output;

  • Low power design, all using DC-DC switching power supply, high efficiency, low power consumption;

  • Industrial standard, no fan structure design;

  • IP40 protection, corrugated high strength shell

Product Introduction:

HS-6206 series is a full Gigabit rail type non network management Industrial Ethernet switch with powerful high-speed communication function independently developed by Chengdu Huashu Communication Technology Co., Ltd. It is a switching device designed with high-speed single chip switching scheme, which uses Ethernet protocol networking in industrial production environment. It is simple, convenient, fast, stable and reliable. It adopts industrial high-strength IP40 shell design with high EMC protection level to ensure the stable and reliable operation of the equipment in the industrial field environment.

The HS-6206 series can support two Gigabit Ethernet fiber-optic SFPs pluggable module interfaces (LC / SC and other interfaces are optional), and four 10 / 100 / 1000Mbps Ethernet interfaces (RJ45). It supports 10Base-T, 100Base TX, 1000Base-T, and full duplex, half duplex and MDI / mdi-x adaption. The fiber-optic interface supports 1000Base-x, and can be in single mode (SM) or multi-mode (mm) mode.


Specifications

Explain

Network standards

IEEE802.3,IEEE802.3u,IEEE802.3x

Supporting media 

10BASE-T CAT3、4、5 UTP(≤100m)

100BASE-TX CAT5 UTP(≤100m)

1000BASE-T CAT6 UTP(≤100m)

SFP pluggable module support: 1000base-x and 100Base-FX, single mode / multimode fiber, LC / SC interface optional

Network interface

4-10 / 100 / 1000Mbps adaptive Ethernet RJ45 shielded ports

2-single mode / multi mode interfaces (LC / SC) for Gigabit SFP modules

Alarm port

One relay normally closed / normally open alarm / I / O port control output

Dial switch

4 bits, super ring function enable / disable, master / slave device setting

Exchange mode

Store and forward

Flow control

Half duplex back pressure, full duplex IEEE802.3x

Spanning tree algorithm

STP/RSTP

Exchange capacity

24Gbps

Packet cache size

4Mbits

MAC address table

8K

Indicator light

Power indication :PWR1,PWR2

Device operation indication: RUN

Ring operation indication: RING

Alarm indication: ALARM

Port indication LINK/ACT, 10m, 100m, 1000m

100 megabyte / Gigabyte optical port indication:LINK/ACT

Transmission distance

Twisted pair 100m (standard CAT3, 4, 5, 6 UTP)

Multimode fiber 850nm, 2km

Multimode fiber 1310nm, 5km

Single mode fiber 1310nm, 20km

Single mode fiber 1310nm, 40km

Single mode fiber 1550nm, 60km

Single mode fiber 1550nm, 80km

Power Supply

Support single / dual 24 VDC redundant input (10 ~ 55 VDC)

Power terminal

4-core 5.08mm spacing terminals, over-voltage, over-current, reverse connection protection, dual power redundancy protection

power waste 

no-load power 2.1W(24VDC/0.09A)
Full load power 3W(24VDC/0.13A)

Working temperature

-40℃-75℃

Storage temperature

-40℃~85℃

Relative humidity

5%~95%(No condensation)

Mechanical structure

IP40 protection grade design, corrugated high strength metal shell

DIN rail type installation is adopted

Size: 137mm x 111mm x 55mm (L x W x H)

Industry standard 

EMI: FCC Part 15,CISPR (EN55022) class A
EMS:EN61000-4-2 (ESD),Level 4
          EN61000-4-3 (RS),Level 3
          EN61000-4-4 (EFT),Level 4
          EN61000-4-5 (Surge),Level 4
          EN61000-4-6 (CS),Level 3
          EN61000-4-8,Level 5

Attack

IEC 60068-2-27

Free fall

IEC 60068-2-32

Shock 

IEC 60068-2-6

Warranty 

5 years

Authentication

CE, FCC, ROHS, UL508 (under certification)

Please check the company's website for the latest certification information

 


Huashucom enterprise content manager system | MetInfo CMS

Brief Introduction

HS-6206 Series Brief Introduction 2.0.pdf


Product Manual

HS-6206 Series Product Manual 1.0.pdf






Model
Port
Power input 
Remarks
1000m electrical port
Gigabit optical port
Interface type
Optical fiber system
HS-6206A-GTX60------DC 10~55V
Standard type
HS-6206A-1GSFP41LC/SCSingle mode / multi modeDC 10~55VStandard type
HS-6206A-2GSFP42LC/SCSingle mode / multi modeDC 10~55V
Standard type
HS-6206B-GTX60------DC 10~55V
Basic type
HS-6206B-1GSFP41LC/SCSingle mode / multi modeDC 10~55VBasic type
HS-6206B-2GSFP42LC/SCSingle mode / multi modeDC 10~55VBasic type


Batch purchase / product customization
【Business Hotline】:028-85199391 or 18980011235
【Contact Email】:652503928@qq.com



Home
Product
Select
Contact us